Just How to Replace a Tub
Just How to Replace a Tub
Blog Article
Here down the page you can discover a bunch of reliable advice in regards to How to Install a Bathtub.
Setting up a tub isn't specifically brain surgery, but it does call for strong plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bathtub with a brand-new one is likewise a reasonably hard project. If the old tub is easily easily accessible, the task can relocate quickly; if you have to open a wall to eliminate the old bathtub and also place the brand-new bath tub, the job is much harder. In either case, the task is within a residence handyman's skills, although you will need an assistant to move out the old tub and set in the brand-new one. See to it you have qualified yourself for the job and are comfortable attempting it. Rather than employing a professional to take over a halfway-completed job, it is better to consider using one prior to you begin. Chances are you might require a specialist plumber to make tube links.
This article will certainly help you set up a brand-new tub in your restroom if you have actually currently acquired a brand-new tub and don't need to change the arrangement of your previous water system pipes.
Your tools and material checklist should consist of the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is detach the supply of water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The process of removing the existing taps can be quite bothersome as a result of the limited access that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a cloth ready for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to carrying on to fit the new taps, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end gives a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly require reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making certain that the washers remain in location in between the faucet and also the sink. Safeguard the faucet in place with the supplier supplied backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former type should be linked to the tap finishes first, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bath tub
Making use of both wood boards under its feet, position the tub in the needed setting. The wooden boards are handy in uniformly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 small factors.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level and adjusting the feet on the tub till the spirit level reads degree.
To mount taps, fit all-time low of the outermost flexible tap port to the ideal supply pipe by making a compression join; after that do the very same for the various other faucet.
Switch on the supply of water and also examine all joints and also new pipework for leaks as well as tighten them if required. Fill up the bath tub as well as also check the overflow outlet and also the regular outlet for leaks.
Lastly, repair the bathroom paneling as defined in the supplier's user's manual. Tiling and sealing around the tub must wait till the tub has actually been utilized at the very least when as this will certainly resolve it into its final setting.
Planning for the Installation
Firstly, the supporting framework provided with the bathroom needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to prevent strain on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you use every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its last placement.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to split a stiff seal, triggering the water to penetrate the wall between the bathroom as well as the tiling, resulting in complications with wetness and also possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your components and also fittings. They are sold in tubes and also cartridges, as well as can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the bathtub with water before sealing, to permit the activity experienced when the tub is in usage. The sealer can crack fairly very early if you do not take into account this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily available on the market. It is advisable to fit the tiles making use of waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on A Step-by-Step Guide to Installing a Bathtub? Put feedback down the page. We would be delighted to find out your thoughts about this page. We hope to see you back again before long. If you please take the time to share this blog posting if you appreciated it. We appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Schedule Today! Report this page